How To Change Water Filter In Whirlpool French Door Refrigerator

Hey, homeowner! How’s your day going? Did you know that your French door refrigerator probably has a water filter? If not, it’s time to learn how to change it!

It’s easier than it sounds. In this article, we’ll show you how to change the water filter in your Whirlpool French door refrigerator step-by-step. So relax and read on. We’ll have you changing that filter like a pro in no time.

How To Change Water Filter In Whirlpool French Door Refrigerator

Where to Find the Water Filter

The water filter is located in the upper right-hand corner of the refrigerator. You’ll need to remove the grill to get to it.

Once you’ve removed the grill, you’ll see the water filter in the upper right-hand corner of the fridge. It’s a black cylinder with a white cap on top. Twist it counterclockwise to remove it and replace it with a new one.

What Tools Are Needed to Change the Water Filter

You will need a Phillips head screwdriver, a water filter, and a container to catch the water from the refrigerator when you remove the old water filter.

The Phillips head screwdriver removes the screws holding the water filter cover. The water filter is released by pushing down the tabs on either side of the filter and pulling it out. Be careful not to spill any of the water in the filter. You can put the new water filter in by pushing it down into place and making sure the tabs are locked into place.

Screw the cover back on with the Phillips head screwdriver. Ensure that the arrows on the body are lined up with the hands on the refrigerator. Put a container under the refrigerator to catch any water that may come out when you remove the old water filter.

Preparing to Install the New Water Filter

Before you begin, unplug the refrigerator and turn off the water supply to the fridge. Then, remove the old water filter by turning it counterclockwise. If it’s difficult to remove, try gently pushing down on it while you twist.

  Samsung Fridge Making Noise When the Door Is Closed

Take the new water filter and insert it into place by turning it clockwise. If it’s difficult to get started, hold the filter firmly and twist it until it’s tight. Ensure the new filter’s gasket is in good condition and that the filters’ arrows are lined up with the indicators on the fridge.

Reattach the water supply line and plug in the refrigerator. Turn on the water supply and check for leaks. If everything looks good, you’re done!

Installing the New Water Filter

Installing the new water filter is fairly simple. First, find the filter cap in the middle of the ceiling inside your refrigerator. This is where you’ll find the water filter. Make sure to turn it 1/4 – 1/2 turn counterclockwise to unlock and remove it.

Next, take the new water filter and remove any protective wrapping or plastic caps. Please insert it into the filter housing with the arrow facing down until it clicks into place. Be sure to hold it firmly to ensure a secure fit. Give it another 1/4 – 1/2 turn clockwise to lock it into place.

Finally, run about a gallon of water through the filter for about three minutes before using it so that you do not get any dirt or particles from installation in your drinking water. And there you have it, as you have successfully installed a new water filter!

Resetting the Refrigerator After Changing the Water Filter

Now that the old filter is out, you need to reset the refrigerator so it recognizes the new filter. To do this, press the Reset Water Filter button for about three seconds. This button is usually located at the top of the display panel.

Once reset, you’ll know it worked if a blue light appears on the water filter icon. If not, give it another reset. It should turn on after your second attempt. After that, you’re all set!

Now that you’ve changed your water filter in your Whirlpool French Door Refrigerator, enjoy drinking clean and healthy water!

  Honeywell Thermostat Says Heat On But No Heat

Troubleshooting Common Issues When Changing the Water Filter

You might run into some issues when changing the water filter in your Whirlpool French Door Refrigerator. These may include a leaking filter, difficulty accessing the old filter, or difficulty removing the old filter.

If you’re having trouble accessing the filter, make sure you remove any shelves in the way and check for any screws holding the casing. If your refrigerator is older, it might also have a latch on the front. If this is the case, you’ll need to access it inside your refrigerator.

If your old filter is still stuck, another potential issue could be that it was not seated tightly enough when inserted. To fix this problem, try firmly pushing the new filter into place.

Finally, if you find leaks at any of the connections along your water line– don’t panic! These leaks can be fixed by securely retightening all fittings and pipe connections and applying a thread sealant.

Conclusion

So, there you have it! Changing the water filter in your French door refrigerator is surprisingly simple and only takes a few minutes. Not only will this help to keep your fridge running smoothly, but it will also help to ensure that your water is clean and safe to drink.

Remember to replace your water filter regularly to keep your fridge running at its best. If you have questions or concerns, consult the owner’s manual or contact the manufacturer’s customer service department. Thanks for reading!

Leave a Comment