How to unlock the whirlpool top load washer

You try to unlock the door, but it doesn’t budge. You’ve just realized you locked yourself out of your whirlpool top load washer. Don’t worry; we’re here to help. In this article, we’ll show you how to unlock your whirlpool top load washer in just a few easy steps.

How to unlock the whirlpool top load washer

Why Is the Whirlpool Top Load Washer Locked?

The Whirlpool top load washer can become locked for several reasons. Most commonly, it’s accidentally locked when someone reaches in to grab a forgotten item and hits the lock button. Other reasons can include a child playing with the controls or a power outage that causes the machine to lock itself.

If your Whirlpool top load washer is locked, you’ll need to unlock it before using it. The process for unlocking it depends on what caused it to lock in the first place. 

If it’s because of a power outage, you can unlock it by pressing the power button. If it’s because of a child playing with the controls, you’ll need to unplug the machine and wait 10 minutes before plugging it back in. Then press the power button to restart it.

How Do I Know if My Washer Is Locked?

If you need to check whether your washer is locked, there are a few ways to prevent it. The most obvious sign is that the washer won’t start up when you try to use it. Another way to tell is if the door is difficult to open or won’t open.

If you’re sure that your washer is locked, there are a few things you can try to unlock it. First, check the manual that came with your washer for instructions. If that doesn’t work, you can unlock it manually.

How to Unlock a Whirlpool Top Load Washer Manually

If you’re having trouble opening the lid of your whirlpool top load washer, you may need to unlock it manually. Here’s how:

  1.     Locate the manual release on the front of your washer. It’s a small, rectangular panel about 2 inches wide and 3 inches high.
  2.     Push in the release with a flathead screwdriver or your thumb, and then pull up on the lid to open it.
  3.     If the release is stuck and you can’t open the lid, try spraying some WD-40 or another lubricant into the opening to help free it up.
  4.     Once the lid is open, add or remove clothes as needed. Be careful not to reach too far into the washer while spinning, as this can be dangerous.
  Whirlpool Cabrio Washer Reset Touch Screen: How To Reset Whirlpool Washer Touch Screen

Troubleshooting Tips for Unlocking a Whirlpool Top Load Washer

The next step is to troubleshoot if the washer won’t unlock. Try these troubleshooting tips if you have difficulty unlocking your whirlpool top load washer.

First, ensure that the power source is securely connected and on. It might be due to a build-up of soap residue in the coin trap or detergent dispenser if it still doesn’t unlock. Try cleaning these out with a moist cloth, and this should help.

If that doesn’t work, you may need to reset the circuit breaker and push the “Start/Pause” button for 5-10 seconds until you hear a chime or see the control panel lock light turn off. 

If this doesn’t work, you might have a defective latch assembly or control board and need to contact customer service for further assistance.

How to Reset a Whirlpool Top Load Washer

If you still cannot unlock your Whirlpool top load washer, the next step is to reset it. To do this, start by unplugging the washer from the power outlet for 10 minutes. After 10 minutes, plug the washer back in and make sure it is on a flat-level surface.

From here, open the control panel and look for an option labeled reset. This will be a button or a switch that can be moved from one position to another. Once you locate this, press it to reset your machine.

After this is done, you should be able to open and close the lid on your Whirlpool top load washer without issue. Make sure to test out the lid by closing it and then trying to open it again before running any loads of laundry through your machine.

What to Do if the Instructions Don’t Work

If the instructions above don’t work, don’t panic! It could be that the washer doesn’t require a special code; some newer models need you to hold down the Start button for three seconds or to activate it through a menu.

  Kenmore series 500 washer troubleshooting

If all else fails, try rebooting your washer. To do this, unplug the washer from the wall and plug it back in after five minutes. Also, make sure there are no clothes in the drum before starting. 

Once you’ve plugged it back in, press and hold the Start button for three seconds, and then try loading a cycle. This should reset any errors and lock out any unwanted users!

You can also check your owner’s manual, as some Whirlpool top loader washers come with a specific reset code that needs to be entered to unlock them. If nothing else works, contact Whirlpool’s customer service for help with unlocking your washer.

Conclusion

If you’re experiencing this issue, all you need to do is to unlock the washer door. Thankfully, it’s a simple process you can do in just a few minutes. Here’s how to do it:

  1.     Open the lid of the washer.
  2.     Look for the small hole on the right side of the door.
  3.     Use a paper clip or a small screwdriver to insert into the hole.
  4.     Turn the screwdriver or paper clip until the door unlocks.
  5.     Open the door and remove your clothes.
  6.     Close the door and insert the screwdriver or paper clip back into the hole.
  7.     Turn the screwdriver or paper clip until the door locks.
  8.     Close the lid of the washer.

Leave a Comment